Amine Adduct Cured Epoxy Finish — Epoxy Protection for Steel and Concrete in Karachi
Amine Adduct Cured Epoxy Finish is a two pack epoxy coating available at Saify Paint House, DHA Karachi. It is designed to protect a range of surfaces from corrosion, including steelwork, galvanised iron, aluminium, concrete, masonry, fibreglass sheeting and phenolic sheeting. If you need a protective finish for industrial equipment or structures, you can compare it with our epoxy paints in Karachi.
The product is supplied as a 5 litre kit: 4.5 litres of base and 0.5 litres of activator. Both parts must be mixed together before use.
Why Choose an Amine Cured Epoxy
Epoxy coatings form a hard, adhesive film that bonds well to prepared metal and masonry. An amine adduct curing system gives the film good resistance to abrasion, water-based solutions and a range of moderate chemicals. The manufacturer also states a dry service temperature limit of up to 104°C.
Key Features
- Corrosion protection: Designed for long-term protection of many surfaces.
- Abrasion resistance: Holds up well to wear on prepared surfaces.
- Chemical resistance: Resists aqueous solutions and a wide range of moderate chemicals, as stated by the manufacturer.
- Heat resistance: Dry service temperature range up to 104°C.
- Low gloss finish: A satin-like finish for industrial surfaces.
- Two colours: White and grey. Custom colours are available on special request.
Recommended Applications
- Steelwork in industrial plants
- Galvanised iron and aluminium surfaces
- Concrete and cement floors
- Plastered walls and masonry
- Fibreglass and phenolic sheeting
For a complete protective system, our team can recommend a compatible primer and topcoat for your surface. You can also browse our full Industrial Paints range. For coastal or splash-zone structures, see our marine paint range.
Technical Information
- Volume solids: 55% ± 2%
- Theoretical spreading rate: 6.8 m² per litre per coat
- Practical spreading rate: 4.1 m² per litre per coat
- Dry film thickness: 80 microns per coat
- Wet film thickness: 150 microns per coat
- Number of coats: Two
- Pot life: 4 hours after mixing
- Dry to touch: 5 hours at 10°C, 3 hours at 20°C, 1 hour at 40°C
- Hard dry: 6 to 8 hours
- Recoat interval: 16 hours minimum, 5 days maximum
- Full cure: 7 days at 20°C
- Flash point: 28°C
- Shelf life: 12 months
Drying and recoat times depend on temperature, humidity and film thickness. Actual coverage depends on the application method, surface roughness and porosity.
Surface Preparation and Application
The surface must be fully dry, clean, free from oil and other contamination, and smooth and sound. Correct preparation affects performance more than any other step, so confirm the preparation required for your structure before you start.
Mix the complete kit together, and use the mixed material within its 4-hour pot life. Do not mix for long periods, because the heat generated shortens the pot life.
Airless spray is preferred when a thicker coat is needed in one pass. Conventional spray is also suitable, using a tip of 0.40 to 0.50 mm at about 2000 psi. Brush and roller can be used for smaller areas.
Do not apply the paint when the humidity is above 85%, or when the air temperature is below 10°C. Do not mix it with other paints, organic solvents or powder materials. Allow at least 16 hours between coats, and no more than 5 days. The coating takes 7 days to fully cure at 20°C, so keep the surface protected during this period.
Storage
Store the product in a dry, shaded place away from direct sunlight, at an ambient temperature above 0°C. It has a shelf life of 12 months. Protect the product from freezing.
Clean-Up
Clean spills, spatters and tools immediately after use with the epoxy thinner recommended for this product. After cleaning, flush spray equipment with mineral spirits to prevent rust. Follow the manufacturer’s safety recommendations when using mineral spirits. Provide adequate ventilation in confined spaces.
Safety Precautions
This product is flammable, with a flash point of 28°C. Keep it away from heat, sparks and open flames. Provide adequate ventilation during application and drying, and avoid breathing spray mist. Avoid contact with eyes and skin, and wash hands after use.
The product contains crystalline silica. Sanding or abrading the dry film may release silica dust, which can cause lung damage and cancer with long-term exposure. Use a NIOSH-approved particulate respirator when sanding, and provide fresh air during application and drying.
In case of eye contact, flush thoroughly with water and seek medical attention if irritation persists. If swallowed, do not induce vomiting, and seek medical attention immediately. Do not take internally. Keep out of reach of children. Read the safety data sheet before use.
Buy Amine Adduct Cured Epoxy Finish in Karachi
Saify Paint House stocks industrial paints and protective coatings for customers across Karachi. Visit our Badar Commercial store at Shop #2, Plot 31-E, 7th Street, DHA Phase 5, or our Gizri store at Shop #2, Al Raheem Center, Main Gizri, opposite Mubarak Masjid, DHA Karachi. If your concrete needs repair before coating, see our building care and maintenance range. You can also learn more about Saify Paint House.
Because this is a two pack product, please message us before ordering. We will confirm colour, stock, the correct primer and topcoat for your surface, and the quantity for your job. For pricing and availability, call 0333-5843610.




