Acrylic Traffic Marking Paint — Road and Car Park Marking in Karachi
Acrylic Traffic Marking Paint is a single pack acrylic coating for marking parking lots, airports and roads, available at Saify Paint House, DHA Karachi. It is designed for professional use on concrete, asphalt and brick surfaces, and it dries quickly enough to reopen areas sooner.
If you are planning a wider surface or road project, you can compare it with our specialty industrial paints in Karachi, which include road marking and sports surface products.
Why Choose an Acrylic Marking Paint
Marking paint has to stay visible under foot and tyre traffic, and it has to dry before traffic returns. An acrylic traffic marking paint formulation gives good abrasion resistance and fast drying, and the manufacturer states that it resists bleeding and dirt.
Key Features
- Abrasion resistant: Designed to withstand foot and vehicle traffic.
- Fast drying: Dry to touch in about 1 hour at 20°C, and 15 minutes at 40°C.
- High visibility: Available in white, yellow and black.
- Reflective option: Glass beads can be dropped onto the wet paint to make reflective markings.
- Good hiding: Provides even coverage with the recommended film thickness.
- Bleed and dirt resistant: As stated by the manufacturer.
- Low VOC: Below 150 g/L, measured by EPA Method 24, as stated by the manufacturer.
Available Colours
Acrylic Traffic Marking Paint is available in white, yellow and black. Mention your preferred colour and pack size when you send your WhatsApp enquiry so we can confirm stock. You can also see our full Industrial Paints range.
Technical Information
- Finish: Flat
- Volume solids: 47% ± 2%
- Weight solids: 70% ± 2%
- Theoretical spreading rate: 3 to 4 m² per litre per coat at 80 to 100 microns dry film. Approximately 220 linear feet of standard 4-inch stripe per gallon.
- Dry film thickness: Up to 100 microns
- Wet film thickness: Up to 250 microns
- Dry to touch: 3 hours at 10°C, 1 hour at 20°C, 15 minutes at 40°C
- Humidity to apply: 50% minimum, 85% maximum
- Recoat interval: 4 hours minimum, 5 days maximum
- Thinning: Not recommended
- Shelf life: 6 months
Drying and recoat times depend on temperature, humidity and film thickness. Spreading rates do not include application losses, so allow extra paint for the surface texture, spillage and the applicator’s technique.
Recommended Applications
- Parking lots and car park bays
- Airport aprons and runway markings
- Road markings and lane lines
- Industrial yards and loading areas
For concrete surfaces that need repair before marking, see our building care and maintenance range.
Surface Preparation and Application
The surface must be clean, dry and in sound condition. Remove all oil, dust, grease, dirt, loose rust and other foreign material before painting. Concrete, asphalt and brick must be fully cured. Freshly laid asphalt often needs to age before painting. If it is not fully cured, apply a thin test coat, about half the recommended film thickness, to check adhesion before painting the whole area.
Mix the paint thoroughly with low speed power agitation before use. Do not thin it. Do not paint on wet surfaces, or when humidity is above 85%. Cool, damp conditions slow drying.
Brush is suitable for small areas only. For larger areas, use a 3/8-inch woven roller cover with a solvent-resistant core, or use conventional or airless spray with a fan tip matched to striping. Working pressure depends on the ambient temperature, so set the pressure to the lowest level that gives a flat line of the correct thickness.
For reflective markings, drop glass beads onto the wet paint. Painted surfaces become slippery when wet, so keep traffic off the marking until it has dried.
Clean-Up
Clean spills, spatters and tools immediately after use with acetone. Flush spray equipment with mineral spirits afterwards to prevent rust. Follow the manufacturer’s safety recommendations when using these solvents.
Safety Precautions
This product is for professional use only. Handle it with care, and read all safety labels on the packaging before and during use. Keep it away from heat, sparks and open flames, since the solvents used for cleaning are highly flammable. Provide adequate ventilation during application and drying. Avoid breathing spray mist, and avoid contact with skin and eyes.
Do not take internally. Keep out of reach of children. Store the containers in a dry, shaded place away from direct sunlight, at an ambient temperature above 10°C. Refer to the manufacturer’s safety data sheet before use.
Buy Acrylic Traffic Marking Paint in Karachi
Saify Paint House stocks industrial paints and protective coatings for customers across Karachi. Visit our Badar Commercial store at Shop #2, Plot 31-E, 7th Street, DHA Phase 5, or our Gizri store at Shop #2, Al Raheem Center, Main Gizri, opposite Mubarak Masjid, DHA Karachi. If you need a more hard-wearing finish for heavy-duty areas, see our polyurethane coatings. You can also learn more about Saify Paint House.
For pricing, pack sizes and availability, message us on WhatsApp or call 0333-5843610.




